![]() Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),Īpproximate round trip times in milli-seconds: Round-trip min/avg/max = 0.000/2.500/10.000 ms sometime got this errorĭestination or WAN interface is wrong! CMD ping WAN Interface:2_voice_internet_r_vid_1849Ħ4 bytes from 10.: seq=0 ttl=64 time=10.000 msĦ4 bytes from 10.: seq=1 ttl=64 time=0.000 msĤ packets transmitted, 4 packets received, 0% packet loss SIP Register address -> gj. Ping Diagnose Server Type - > SOFT SWITCH SIP / IMS SIP Hope that you get your VOIP going as well. I am willing to help at my spare / free time only, through email only no remote configuration. Refer to Zoiper5 settings as they are same on android too. It will display something like checking status and then 10 - 15 seconds later it will be registered.ģ9. Protocol - UDP (TCP connects but I didn't get any sound).ģ8. Advanced SIP settings - outbound proxy same as SIP Server.ģ6. +91 + std code without leading zero + your number).ģ5. ![]() SIP Server - gj. (your circle might have utstarcom core instead of huawei, if so, use gj.).ģ4.Username - is your phone number (eg. Go to call settings - calling accounts - add SIP account.ģ3. Zoiper will show which protocol it found and add the account and make it active.ģ2. Leave authentication username id empty.ģ1. ![]() Outbound proxy - gj. (your circle might have utstarcom core instead of huawei, if so, use gj.).ģ0. Tick authentication and outbound proxy.Ģ9. SIP Server - gj. (your circle might have utstarcom core instead of huawei, if so, use gj.).Ģ8. +91 + std code without leading zero + your number).Ģ6. It may take many tries (5 to 10 minutes before being successful).Ģ6. If all goes well you'll be registered and see green icon on MicroSIP. SIP Server/Proxy/Domain is gj. (your circle might have utstarcom core instead of Huawei, if so, use gj.).Ģ4. +91 + std code without leading zero + your number).Ģ1. Username, Login, Display name is your phone number (eg. Download MicroSIP or Zoiper5 on Windows PC (MicroSIP is available for Linux too)Ģ0. If ping okay then continue else you messed up something, try again from the beginning.ġ9. Ping your default VOIP gateway(10.x.x.x) from a PC connected to the router network (eg. Enable DHCP in router and change DNS as above in point 5.ġ8. Set the Router LAN IP to anything other than 192.168.1.x subnet (eg. Open Router admin page and set its WAN to Static IP and enter one of the ONT LAN IP (eg. Insert LAN Cable in the Port selected in point 1 and connect other end to WAN of any old Wireless / Wired Router.ġ3. (Enable if disabled then disable again, i don't know why this works).ġ2. Add Static Route to ONT Destination - 10.0.0.0 Subnet - 255.0.0.0 Gateway - YOUR VOIP Gateway(10.x.x.x) Metric - 0 Interface - VOICE_INTERNET.ġ1. Change VOICE Profile in Network to VOICE_INTERNET. *** You must have a proper working VOIP Profile set in your ONT, i.e., your ONT should show your VOIP number as Registered.ġ. I have a Fiber Basic Plan for testing purpose on which I have somehow managed to get VOIP working decently.īelow is what I did (summarized) - ONT - Syrotech (WIFI Model with 2GB LANS + 1 POTS). Incoming calls should be working fine after that.I wanted to share with you the basic BSNL FTTH VOIP configuration for Gujarat region.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |